클잼 로고

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Repairs to uPVC Windows

uPVC windows are a fantastic option for modern homes. They are long-lasting, durable and easy to maintain. As opposed to aluminium and timber they don't corrosion or rot.

It is crucial to wash and oil UPVC windows and doors regularly. This will reduce repair costs and improve energy efficiency.

1. Broken Glass

The broken glass in your windows can cause serious damage to your home and even be fatal. It is essential to make sure that your windows are in good working order.

Single-pane windows are relatively simple to replace, and they generally fit into frames of the past easily. If you have double glazing-paned windows that are held together by internal beading, it is harder to remove and replace the panes that were previously in use. In this case you'll need to source some plastic spacers that help the new pane to fit properly into the window frame.

If you're planning to attempt to remove the glass panes yourself it is crucial to wear the proper safety gear such as gloves that are thick and protective eyewear. It is also recommended to lay down a drop cloth before you start working on the glass, so that any shards will fall onto the fabric instead of onto the floor where they can be trampled upon and cause further damage.

Once the glass is removed and the glass is removed, it's a good idea to cover the gap with packaging tape or duct tape to block drafts and water from entering the home until a professional is able to come out and uPVC repair repair the window. This also serves as an obstacle to stop intruders from getting into your home. If the gap is large, you might want to consider using a security door that has an integrated window as it offers the best of both worlds.

2. Sagging

uPVC windows and doors are a low-cost energy efficient, durable and long-lasting alternative to timber windows with sash. In time, they could develop a number of problems, including sliding. A sagging window can cause problems with light, draughts, and even security. It's important to take action when you realize that your uPVC windows are falling down.

To fix a window that is sagging you can try to reposition the hinges. First, you'll need to unblock the windows so you can access the frame. Then, using an screwdriver, take off the hinges on the top and bottom and adjust them by turning them clockwise or anti-clockwise. Close your window to check the fit after having moved your hinges. If you're happy with the fit, tighten the screws to ensure that they stay in place.

If you aren't able to move the hinges you may need to replace the seal. Rubber seals can dry out and lose their elasticity with time, causing them to lose their tightness. It is crucial to replace your seal as quickly as you can in order to keep your uPVC window waterproof and draughtproof.

uPVC handles can also become loose. Most often, this is caused by screws that have come loose over time. However, uPVC repair it could also happen because the handle mechanism has worn out. It's relatively easy to repair a loose uPVC handle. You'll first need to close the window and perform an initial fitting. The corners of the sash must be aligned with the casing joint. If it isn't, you can use a screwdriver to loosen the handle, and then return the mechanism to its original position.

3. Water Leaks

If you wake up to wet floors and mouldy walls each time it rains, it's crucial to take action. Windows that leak water do can not only cause degradation of your home's structure but also hamper your efforts to control the temperature inside your home. Most often, uPVC window leaks are caused by a lack or damage to the sealant.

This is an easy fix that can be done by any DIYer who has the ability. Depending on how serious the issue is, old caulking might need to be removed. When it is time to uPVC repair, you should avoid over-caulking. This can make your window harder to clean and lower its energy efficiency.

Make sure that the drainage holes do not have debris inside them and ensure that the sill pan is angled correctly to drain away from the window. In more serious instances, you may need to replace the window.

Other signs of long-term water leakage are sills that are rotten and the appearance of black spots of mold on the wall near the window. This fungus thrives under humid conditions and can propagate quickly throughout the home.

If the leakage is occurring between the double glazing-glazed glass, it is more likely the problem is with the seal rather than the frame. Again this can easily be corrected by an uPVC window expert who can replace the glass seal and restore the full insulation properties of your windows.

4. Faulty Hinges

If your uPVC windows are brittle to open, or are loose and blow open in a breeze, it may be hinges at fault. They can be easily replaced by any competent DIYer and can usually be completed in a matter of minutes.

Like all mechanical parts hinges will be damaged over time. The process of replacing a hinge on a window is essentially a very simple procedure, but it is simpler when you have a person to assist in holding the frame up.

It is also important to verify that the uPVC hinges are opening and closed in the correct direction. This can be done by looking for the arrows on each hinge. This indicates which way the window should open.

The issue could be caused by opening the window incorrectly or by a poor installation in the factory. It is usually possible to fix the issue by sending us a photograph on our website. We will be more than happy to give you advice.

Regular lubrication of hinges is also essential. Applying a light engineering lubricant on the hinges is a great method of doing this. We suggest using an oil that does not contain solvents, such as 3-in-1 Multi-Purpose oil. Regular lubrication can help the window open and close more easily. It can also reduce the possibility of a window sticking and help prevent corrosion. This should be done at least every year. WD40 and other solvent based lubricants are not recommended as they can damage the parts of your uPVC window.

5. Draughts

Draughts can be caused by a variety of different things. Firstly the hinges, again because of wear and tear, could become misaligned. This causes gaps to develop where the sash meets the frame. If they are damaged beyond repair, it might be required to realign them. The interlock, which is located on the hinge side of the window, can also become misaligned, again it may be possible to just give them a clean but in some instances it could be necessary to have these replaced.

The next common reason for draughts are the window seals. These are susceptible to being worn out or damaged over time and let air escape through these gaps. This can be avoided by replacing them with high-quality weatherstripping. Replace the windows made of upvc with low-emissivity lenses. This will help to regulate indoor temperatures and lessen the risk of draughts.

Another, and most effective ways to reduce the draughts in your home is to use an draught excluder. These are typically fabric tubes filled with some type of filler. They can be placed on the windowsill on top. These will keep your home warm by blocking cold air.

Your windows made of upvc will remain a great source of insulation and security in your home with regular maintenance and repairs. It is essential to remember that all windows eventually get worn out and it may be cheaper to replace them than to repair them. If you encounter any issues with your window made of upvc you should consult an expert immediately.