클잼 로고

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

UPVC Window Handle Replacement

Replacing a damaged or broken window handle is a easy process, and with the right tools it can be done quite quickly. It is important to identify the kind of handle you have and the spindle's size before you purchase the replacement.

Older uPVC window handles have a spur which protrudes and locks over a wedge striker. They can be right or left-handed and have to be matched when replacing.

What type of lock or handle do I have

There are many upvc window locks and handles, each with its particular advantages and uses. The type of handle you have will determine how easy it is to open your windows and whether or not the locking mechanism works as intended. Over time, and with regular use, the upvc handles on your windows may become damaged and worn out. This makes them less secure and less effective. In some cases they may even fall completely off. It is essential to fix your window handles made of upvc when you see them falling off. This will stop possible burglaries and will keep your home secure.

It's a task that almost anyone can do. With a few basic tools and the right information it's a straightforward process that shouldn't take more than a couple minutes. You must know the type of handle or lock that you have on your window. This will help you select the right replacement.

Inline Espagnolette Handles

They are typically located on the side of the window. They have a flat design and have an opening that is connected to the locking mechanism of the window frame when it is turned. Inline upvc handles have a spindle that runs through the middle of the handle into the window frame to operate the latch.

Cockspur Handles

They are typically found on older uPVC window frames and feature a distinctive, hook-shaped design. Cockspur handles are attached to the frame of the window by only one screw and are less secure than other varieties of window handles.

Tilt and Turn Handles

The tilt and turn handles are different from other upvc handles because they can be turned to open the window and then lowered into the window to allow air circulation. They typically have a 7mm spindle on the side of the handle. They are available in left and right-handed versions.

It is important to measure the spindle size when buying replacement upvc handle. Not all of them are exactly the same size. Drop something into the middle of the hole to check the length. This is the maximum size of spindle that will fit into your windows.

What is the spindle?

uPVC window handles operate in a similar way to doors, by turning the handle to operate a latch inside the frame. The window is then opened and closed. However, sometimes these handles can become damaged, especially when they are used frequently or exposed to extreme weather conditions. You may need to replace the handles on your uPVC window if they are not functioning correctly.

There are a variety of uPVC handles available including Espag, Cockspur and Spaded handles. They are designed in a variety of ways to fit into uPVC frames. Each handle type utilizes an entirely different spindle for locking the window mechanism. This is why it is important to identify the type of handle you have installed on your uPVC window so you can get the correct double glazing replacement window.

The base section of the handle will tell the type of uPVC it is. A snap-in covers should be over the screw that holds the base of the handle in position. After removing this and you'll be able to see the screw that holds the handle base in position. After both screws are removed you should be in a position to pull the handle away from the uPVC window.

After taking off the uPVC handle, carefully remove it from the locking mechanism. Take note of the length of the spindle. You will need to purchase a replacement with the same length as the handle that was originally used and locking device.

The most common issue with uPVC window handle problems is that the spindle gets worn-out and is unable to longer function properly with the locking mechanism. This could be due to corrosion, damage from continuous use, or even an unreliable locking mechanism. If this happens, it is required to replace the window handle as well as the locking mechanism to restore complete functionality to your uPVC windows.

How do I get rid of the handle that was previously attached?

Window handles are susceptible to being damaged or even broken over the course of time. It is important to repair them as quickly as you can to ensure your security. It is easy to replace a worn or damaged handle. The task can be accomplished in under an hour without the need for any special tools.

The first step to remove the handle that was previously used is to remove the screw that is located at the top of the base of the handle. After the screw is removed, the handle will be removed. There is a second screw that is located at the bottom of the handle's base and it can be removed too. After both screws are removed the handle can be completely detached from the base section of the window.

After the handle has been removed, grab the new handle and align the fixing holes with the holes that are currently in the window frame. There might be a small cap or sticker on the new handle, so remove them if needed and then screw the handle into the frame. Once the handle is set, it is important to test whether it functions by turning the handle, and ensuring that the lock mechanism is activated.

Espag handles have a spindle which protrudes out of the handle and slots into the multipoint locking mechanism of the frame of the window. Cadenza windows have blades with cut-outs that slot into the lock mechanism, while Cockspur handles have a long nose that is able to hook over either the frame's outer or the transom bar cross member in the window.

Once you have the new handle in place, slide the spindle into the lock inside the window and then tighten it. Replace the snap-in cover and screw cap (if necessary) after the handle has been firmly fixed. The handle is now ready to use to use, so try opening and closing the window several times to check that it works well and securely.

How do I install the new handle?

Switching your uPVC double glazing window replacement handle isn't difficult and the process is actually very simple. All you require is a screwdriver and small amount of patience. First, make sure that the handle is not locked. Remove any screws that are visible. You could also replace them with screw caps. After removing the handle, you'll need to record the length of the spindle which extends from the back. This is crucial as it will determine what kind of handle you will need to buy.

Espagnolette handles are the most popular type of handle for uPVC windows. The spindle passes through the handle to operate the locking mechanism within the frame of the window. Once the handle is turned it opens the latch on the window and allows it to open. During regular use and over time, handles for espagnolette may be damaged.

Cadenza handles are a type of uPVC handle that is usually used with tilt and turn windows. They have an extended blade that works the multipoint locking mechanism inside the window. They are usually more secure than handles made of espagnolette because they are only accessible from the inside. They can be replaced by the same procedure as espagnolette handles but you should make sure that the new handle has a curved blade instead of flat ones.

After you have picked the right handle, simply align the new handle to existing screw holes prior to screwing it in place. Then, you should put the screw covers on and test your new handle. This is accomplished by shifting the handle from the locked position to the unlocked and vice versa a few times. It is possible to contact an expert to determine how you can fix any problems. They can often advise you on the best way to resolve the issue in a fast and effective manner.