클잼 로고

• 목록
• 답변
• 글쓰기
• 게시판 리스트 옵션
  • 수정
  • 삭제

Reasons Your fiat keys replacement 500 Key Fob Won't Work

A key fob for fiat 500 key Replacement uk 500 makes it simple to open doors and start your vehicle. However, there are many reasons the fob could stop functioning. These include a dead battery or water damage, receiver module issues, or interference.

This listing is for a NEW replacement Fiat Flip Key Remote - look-alike Ilco brand that needs to be professionally programmed by a local automotive locksmith (click here to search for a Locksmith Search). This remote includes lock, unlock and trunk buttons.

Dead Coin Battery

The most frequent reason why the 500 key fob won't work is an inactive battery. Modern key fobs have only a limited range of operation and must be within a few inches of the vehicle in order to function. If you are not within your vehicle, and you hit the keyfob, it won't respond and display the message "Key Fob Not Detected".

If this occurs you need to replace the battery of your coin-cell (Part Number CR2032) by a fresh one of a reputable brand such as Panasonic Duracell or Energizer. You can typically find them in your local hardware store or on the internet.

You can test the coin-cell battery by pressing the buttons while standing near your Fiat 500. The parking lights should flash and the key fob should operate the lock and unlock switches.

If your fob's key does not work after replacing the battery, it may be water damage which prevents it from communicating with the module in your vehicle. Water damage can happen in many ways, including the simple splash or submerging the key fob saltwater at the beach. If you suspect your fob was exposed to water, put it in a dry rice bag to draw the moisture out. If that doesn't work your fob will probably require reprogramming by an experienced auto locksmith or the dealer.

Water Damage

The fob does have rubber seals to keep water out of the chip's electronic circuit and out of the ocean or washing it in a machine can cause water damage. Saltwater poses a particular risk to the fob's circuit board which causes it to short out and eventually die. In the event that you let your fob get wet, it's not a good idea but if you accidentally drop it in a glass of water or do not remember to remove it from your pants pocket before running the washer, don't give up hope.

First remove the battery from the fob. Before replacing the battery clean the electronic chip with isopropyl or fiat 500 key Replacement Uk similar products. Check the fob to check if it's working. If the key does not function, it may have to be programmed again. This is usually done by an auto locksmith or dealer.

If the key is newer and was not programmed to your car It will most likely need to be replaced completely. This is an easy process that can be completed by a professional automotive locksmith. The locksmith needs to cut the key to match the ignition of your car. They will also need to reprogram the fob in the system of your car. It's a simple and cost-effective process that is usually completed in the same day.

Receiver Module Issues

The 500 key fob you have may not work because it's out of range. The remote's range is of 30 feet, so should you be too far from your car it won't respond to your commands. It's easy to fix this by moving the remote closer to your car until it responds.

If your fob isn't working after replacing the battery for the coin, also called a "button", "watch" or "button" it could be due to a problem with the internal circuit board. Reprogramming your fob can resolve this problem. You can find the instructions on how to start a fiat 500x with key to do this on the majority of automobiles by searching YouTube or looking through the owner's manual.

It's possible that you need to replace the metal retaining clips that hold the coin battery in place. If they become loose, it could prevent your coin battery from sitting properly, causing your remote to malfunction.

In rare cases the fob might be out of connection with your vehicle as a result of hardware or software issues. This can be a major headache, but you can frequently fix this issue by visiting a local dealer or auto locksmith to have them reprogram your fob for you. In certain instances, they may need to reinstall the software in your body control module as well.

Interference

Interference can also cause the key fob to not receive or transmit a signal. This is possible when the key fob is close to the radio transmitter (cell phones, radar detectors) or another source of electromagnetic radiation. Other reasons the key fob might not work may be a lack of connection to the buttons and internal chip, or water damage.

If your key fob suddenly stopped working, or if you have tried everything at home to solve the issue (e.g. replacing batteries, reprogramming or using the spare key fob, you may have a faulty receiver module on your 500. The receiver module is situated under the dash and picks up the radio frequency signals from the key fob. It transforms the signals into electronic commands which are then processed by the vehicle.

Luckily, there is an easy method to reset all of the on-board systems in your 500 and include the key fob. Disconnect the battery 12 volt for about 15 minutes, by removing the negative cable and then the positive cable. Then reconnect the battery. This will clear out any residual electricity and restart the car's computer system, which can help you get your key fob working again. If the problem persists you should speak with an expert technician. They can identify the exact cause of any problems.